Custom Flanges

THE HOME OF THE TRULY HIGH ANGLE AND LONG TRAVEL DRIVE SHAFTS

When you order online or by phone, we guarantee that we will guide you if we see any problems with information you provided. You will get what you need.

Below you will find solutions to any problems you are having with drive shafts. We have manufactured a complete set of solutions so that there are very few if any problems you are having that we have not addressed.



SYE Kits                    LONG TRAVEL       ROVER, SUZUKI, TOY    BLAZERs + JEEPS+OTHERS    PERF 45    BBjr 60/Bad Boy80                                                 yokes            HI ANGLE LONG SPLINES



Blazers 1350         1350 32 spline     Universal 32 SPL Suzuki          HD Buggy Axles 930 hubs

CV 32 SPL 208TC 205,Atlas,All Kits Ford,Chvy,Dodg,Toy           Half ton/One ton long spline 35

TOP OF EACH WEB PAGE ARE THE SAME, SCROLL DOWN AFTER EACH PAGE FOR CONTENT

SHOPPING CART SPECIALS

                                A) NP231 SYE KIT start at $325 includes CV drive shaft.    Click & see

                         B) Heavy duty Short Shaft Kits With new shaft and housing etc... Click to see

                         C) 10% Off when you buy a stock drive shaft Online.

                         D) 930 Buggy axles Can not be beat !!!

CLICK BEST SELLER DRIVE SHAFT SHORTCUTS BELOW

You may cancel or delete selected items at any time before submitting a purchase

HOW TO MEASURE A DRIVE SHAFT

New Products / Wrangler Options / JK Jeep kit / CJ Drive Shafts / Chevy Rear Shaft / Chevy Frt

Chevy HD Drive Shafts /Toyota Frnt &Rear Shafts / Ford Super Duty/Dodge Drive Shafts

Ford-Chevy-Dodge-Jeep-Blazer SYEs / Chevy S10 Front / S10 Stock rear / S10 231 SYE

Bronco / Rubicon Shafts / Land Rover / Low Riders / Two CV Shafts / Long Travel / U-joints

Buggy Axles / SYE & Shaft / Tranny Yokes / Trans Case Yokes / Weld Yokes / Custom Flanges

Eliminate Slip Yoke/ Non-Serv Shafts / Hi Angle CV 40 deg Shafts / H Angle 50,60,80 CVs

Drive Shaft Parts /Stock Shafts / No CV Shafts / D300 CV Yokes / Dana20 CV Yokes / Long Spline

Link Trades : You verify our site and we check yours.

World Class Driveshafts
800-845-6326 602-253-8006 602-253-8208

ADDRESS

2417 WEST Lincoln St Phoenix AZ 85009

Custom Flanges
CLICK FOR DIFFERENTIAL YOKES
REMEMBER WE CAN DO ANY FLANGE OR YOKE, JUST CALL US WITH SPECIFICATIONS

Atlas II, NP 205 or 203 bolt-on 32 Spline flange   3.0" center to center side to side not cris-cross with 2" pilot

This flange is built custom at Drive Shaft Superstore

A 1350 CV drive shaft can bolt to this large 4 bolt flange -- $165.00

For Saginaw GM flange
(where a GM front CV is used at the rear of the 205 or 203 TC) -- $165.00

Pilot is 3.125"

NP205 transfer case front flange with 10 splines, 30 splines or any spline count you may need.     3.0" center to center side to side not cris-cross with 2" pilot

A 1350 CV drive shaft can bolt to this large 4 bolt flange -- $165.00

A Saginaw GM CV can bolt on to this 4 flantge - $165.00

Pilot is 3.125"

Dana 20 transfer front flange 10 spline flange   3.0" center to center side to side not cris-cross with 2" pilot

A 1350 CV drive shaft can bolt to this large 4 bolt flange -- $165.00

Saginaw GM flange - $165.00

Pilot is 3.125"

Ford 30 spline 8.8 Differential flange

3” center to center of holes side to side not Cris-cross and a 2” pilot

Ford flange -- $65.00

      Pilot is 2"

Ford flange blank splines, press in your own splines -- $25.00
Pilot is 2"

Toyota hole pattern
with a 1310 spicer u-joint

Toyota hole pattern (2 ¼ x 2 ½ 1983 and earlier small holes) -- $40.00

Toyota hole pattern 2 3/8 square pattern 1984 and up -- $40.00

Suzuki flanges to fit large or small bolt patterns

30 degree flanges 1310 u-joints

Suzuki flange (Small hole pattern) -- $65.00
All 1310 half ton u-joints not the little ones.

Suzuki flange (Large hole pattern) -- $65.00
All 1310 half ton u-joints not the little ones.

All 1310 half ton u-joints not the little ones.

Suzuki CV flange small hole pattern -- $125.00

Small hole pattern 1988 and below
Suzuki CV flange Large hole pattern -- $125.00

Large hole pattern 1988.5 and up

Bronco II flange

2.5" c-c of hole 2" pilot. 1310 half-ton u-joints

Bronco II flanges -- $25.00

These flanges used to replace the OEM cv style housings. Works great

Land Rover flanges

We make heavy duty drive shafts too. These flanges take a 1310 u-joint

Land Rover flanges -- $65.00 each

WE CAN DO JUST ABOUT ANY YOKE Or FLANGE    CALL AND ASK US PLEASE

ANY UJOINT OF OURS BREAKS WE REPLACE IT FREE OF CHARGE